thingiverse
FF Creator Pro Dual Fan Duct
My take on the Flashforge Creator Pro Dual Fan Duct ;-) Remixed from: - FlashForge ...
tape creator pro 3D Models
428 resultsSponsored
thingiverse
thingiverse
EKWB ek-xres revo d5 Mount
This mount for EKWB x-res revo d5. I used 3m tape to install. Print Settings Printer Br...
thingiverse
Simple Spool Holder for Flashforges and Replicators
This is my take on a spool holder for a Makerbot Replicator 2x and Flashforge Creator p...
thingiverse
Guitar Picks Holder (Wall Mount)
For keep your guitar pick in place. After print, use double sided tape to mount printed...
thingiverse
C210 Logitech webcam mount for FF Creator Pro
This is a mount for a C210 Logitech webcam for the FlashForge Creator Pro. It uses the...
thingiverse
FlashForge Creator Pro SD Card Slot Cover
The exposed nature of the SD card slot on my FlashForge Creator Pro bothers me, so I kn...
SPONSORED
📈 Will the Fed cut interest rates in July?
Wall Street vs. the crowd. Who predicts the Fed correctly?
thingiverse
2014 and Below Flashforge Creator Pro Offset Universal Spool Holder
This is a remix of 2015 Flashforge Creator Pro Universal Spool Holder by Davefx and Upd...
thingiverse
Filament Spool Holder 31mm x 90mm Long - Flashforge Creator
Spool holder for Flashforge Creator Pro 2016 2 x Screws 3mm x 8-15mm needed Diameter 3...
prusaprinters
C210 Logitech webcam mount for FF Creator Pro
This is a mount for a C210 Logitech webcam for the FlashForge Creator Pro. It uses the ...
thingiverse
Tyranitar Comb
Now you can take care of your pokémon's hair with this Tyranitar-shaped comb, out of Po...
prusaprinters
Spice rack by jopoma remixed
I took Spice rack by jopoma and filled in the back so I could mount it with double stic...
thingiverse
Flash Forge Creator Pro Handle Covers
Handle covers designed for the Flash Forge Creator Pro to retain warm air and/or reduce...
thingiverse
1/4" (6.35mm) Z Axis Spacer
This is a 1/4" (6.35mm) spacer for PowerSpec 3D X Dual Extruder Printer, FlashForge Cre...
prusaprinters
Toothbrush Holder
Just attach the double-face tape to the back and stick it to the wall. the electric too...
thingiverse
Badge for Flashforge Creator Pro
This is a badge I made for the Flashforge Creator Pro. It affixes to the extruder carr...
thingiverse
Headphone Hanger
I made this little hanger to get my headphones off my desk and free up some precious re...
thingiverse
Push Latch
This is for a project where I 3d print onto duck tape. It will be printed onto duck tap...
thingiverse
Helinox Chair Replacment Foot
Replacment foot for helinox camping chair Print Settings Printer: ...
thingiverse
Anet Motherboard - RPi - 2 Mosfet Board
I wanted an enclose all the Anet A8 MB-Pi-USB to 5v-2xMosfet boards. It is split in two...
thingiverse
Parallax Servo Front/Bottom Mounts
These servo holders attach to both the front mounting holes on the Parallax Standard Se...
thingiverse
Mini 4x Cable Holder for iPhone & Android
Here a very small cable holder for iPhone or Android USB cable Easy to fix with Double ...
thingiverse
slot in active ventilation fan mount
Flashforge creator pro slot in 80mm fan mount, slots into the acrylic hood and directs ...
thingiverse
Flashforge Creator Pro Dome hinge
Hello, This is a Hinge for the dome of the Creator Pro, i was tired of moving the thing...
thingiverse
Micro Sanding Block
Inspired by the Micro Zip Sanding Block, this little gadget is useful for post processi...
thingiverse
Ipad cord keeper
I needed a way to keep my Ipad Pro cord contained since it is a pretty long cord, this ...
thingiverse
Nvidia Shield Android TV Stand
Very quick design, almost copy of original, fit well, feels solid so far no issue:) Pri...
prusaprinters
108mm Large Fire Extinguisher Holder Bracket
Resized Fire Extinguisher or Gas Torch Holder by The_BeardBot to fit my larger 108mm di...
thingiverse
Under desk headphone mount
This was my first time designing any three dimensional. I used Autodesk Fusion 360. I u...
prusaprinters
Spice rack by jopoma remixed
I took Spice rack by jopoma and filled in the back so I could mount it with double stic...
thingiverse
Sample Spool
I had some tangled samples of filament and needed a spool so designed it to fit the spo...
Sponsored
Sponsored