5kg spool holder 3D Models

XL Spool Holder (1KG, 3KG, and 5KG Spools)

This is my filament spool holder for 5kg spools. Need this for a large print job I am a...

XL Spool Holder (1KG, 3KG, and 5KG Spools)

This is my filament spool holder for 5kg spools. Need this for a large print job I am a...

3kg and 5kg spool holder

cctree 3 kg and 5 kg spool holder

DigitMakers Spool Holder For 5KG , 3KG and 1KG

The Spool Holder is designed to handle our Esun PLA+ 5KG Spools & D3D 5KG Spools but it...

Shelf spool holder (5kg spools)

well the 5 kg spool don't fit on a 3D printer so i have designed some brackets to mount...

5kg Spool Holder

Update: Added version for Axel with hole for 8mm or 5/16 metalic rod if you feel you ne...

5Kg Spool holder

5kg spool holder

Spool holder to fit the large 5kg spools with a 113mm hole uses 608 bearings. ...

5KG spool holder

this was the original - https://www.thingiverse.com/thing:3353204 I could not add his a...

5kg spool holder

Just needed a bigger holder and figured id upload it here. I bought a 5kg instead of a ...

5kg spool holder

5kg spool holder

5KG spool holder

Simple remix to fit a 256x256 bed. Good amount smaller yet just as strong. I also jus...

5kg Spool Holder

Holder for 5kg rolls of filament

5kg Spool Holder

3 part design for eSun 5kg spool, no bearings or extra parts needed. Many designs f...

5KG spool holder

this was the original - https://www.thingiverse.com/thing:3353204 I could not add his ...

5KG spool holder

5KG spool holder! V2 has 3/8 threaded rod hole for support! may also need to print ...

5Kg Spool Holder

I recently purchased a few 5Kg spools from Zyltech but soon realized it was too heavy f...

5kg Spool Holder

Holder for 5kg spools of filament

Prusament 1kg/2kg spool holder

This is an adjustable spool holder, which can assembled in various widths. Simple inser...

Spool Holder - 2kg, 1kg, 250g

You will need bearings.for 2kg three 608for 1kg two 608for 250g two 696Among the STL fi...

Spool holder 1kg, 2,1kg, 3kg

.gcode file is already made and slice by simplify3D inside the folder with the same par...

Spool Holder for 3kg and 1kg spool

It's assembled on 4х 608zz bearings.Includes two rollerLong for 3kg and 1kg spoolsShort...

5kg spool holder 2020

You will need additional hardware for this to work x4 M7x45mm nuts and bolts or longer ...

Large Spool Holder (5kg)

Large filament holder designed specifically with Makerbots 5kg spool in mind however an...

Zyltech 5kg spool holder

I love the convenience of Zyltech's 5KG rolls, but I've had issues with the filament sp...

ZYLtech 5KG spool holder

I stretched this to fit the zyltech 5KG spool, I also edited the existing braces to acc...

Large 5KG Spool Holder

I needed a spool holder that was compatable with a 5KG roll of filament. Had a hard tim...

Zyltech 5kg spool holder

This is a remix of the spool holder that I use the most. It's designed a little differe...

1kg to 3kg Fillament Spool Holder

After I did my remake of the Ikea Lack Table Housing I needed a spool holder to just si...

Section spool holder 3kg spools

BOM:n° 1 M8 threaded rod ( for a single "Section" use about 155 mm of rod)n° 8 washers ...